Search Results

It aims to study the unsteady flow characteristic of the side-view mirror wake field, and reduce the wind noise by means of unsteady flow control. In this paper, the PIV test in a wind tunnel is used to capture the unsteady flow in the wake field of the side-view mirror, which is used to verify the accuracy of the steady simulation method with RANS after being averaged. Then LES turbulence model is used to obtain the wind noise, and the unsteady flow characteristic like vortex shedding of the side-view mirror is studied. The results show that, in the wake of the side-view mirror, there is a vortex pair similar to Karman Vortex Street. In both horizontal and vertical sections, these two vortexes are respectively separated from the upper and lower edges of the side-view mirror. Accompanied by a significantly uncertain periodic shedding, they continue to extend back until dissipating.

The thermal management system of the water medium retarder using engine coolant (water and ethylene glycol) as transmission medium, omits oil-water heat exchanger in the structure. When the hydraulic retarder is operated, the valve is connected with the retarder and water pump, and then the engine coolant enters the working chamber. The kinetic energy of the vehicle is converted into internal energy of the coolant, and the heat is discharged to the external environment through the engine thermal management system. The braking torque of the water medium hydraulic retarder is determined by the water medium flow rate in the working chamber. The smaller the valve opening degree, the greater the braking torque and the faster the heating transmission fluid. Small valve opening is not conducive to the loss of heat. It will affect the normal working of the engine and hydraulic retarder.

Based on the research and analysis of the current brake systems, this paper presents a novel electro-hydraulic brake system, which can better meet the functional requirements. The system mainly contains a master cylinder, two brake hydraulic cylinders and drive motors, two transmission mechanisms, thirteen solenoid valves, pedal force simulator, etc. Since the proposed brake system uses a dual motor along with two brake hydraulic cylinders, it has advantages in providing fast pressure response, flexible working modes, high precision and strong fault tolerance. In order to facilitate the study of pressure control algorithm for the proposed brake system, a mathematical model of the brake system is firstly established, then a multiplexed time-division pressure control algorithm is proposed to realize the simultaneous or partially simultaneous pressure control, which ensures the high precision and short response time.

The slip ratio of vehicle driving wheels is easily beyond a reasonable range in the complex and changeable driving conditions. In order to achieve the adaptive acceleration slip regulation of four-wheel driving (4WD) vehicle, a fuzzy control strategy of Automatic Drive Train Management (ADM) system based on road situation identification was proposed in this paper. Firstly, the influence on the control strategy of ADM system was analyzed from two aspects, which included the different road adhesion coefficients and the vehicle’s ramp driving state. In the meantime several quantitative expressions of relevant control parameters were derived. Secondly, the fuzzy logic control algorithm was adopted to design a road situation identification subsystem and a ramp driving state identification subsystem respectively. The former was based on the μ-S curve model, and the latter was based on the vehicle driving equilibrium equation.

A braking force distribution strategy in integrated braking system composed of the main braking system and the auxiliary braking system based on braking pad wear control and hitch force control under non-emergency braking condition is proposed based on the Electronically Controlled Braking System (EBS) to reduce the difference in braking pad wear between different axles and to decrease hitch force between tractors and trailers. The proposed strategy distributes the braking force based on the desired braking intensity, the degree of the braking pad wear and the limits of certain braking regulations to solve the coupling problems between braking safety, economical efficiency of braking and the comfort of drivers. Computer co-simulations of the proposed strategy are performed.

In contrast to functionality and reliability, which are more and more assumed to be a natural and necessary condition of any vehicle, the performance of Noise, Vibration and Harshness (NVH) now belongs to those features which play an essential role for the customer's purchasing decision. Sound design and vehicle interior noise control are essential parts of NVH. One tool of the NVH solution toolbox is Active Noise Control (ANC). ANC technology aims to cancel unwanted noise by generating an “anti-noise” with equal amplitude and opposite phase. Owing to the fact that human hearing has selective sensitivity for different critical bands, a new control strategy of ANC, which selectively controls the noise of specific bandwidths according to the result of specific loudness and retains the part of noise created by the normal running of facilities, trying to attenuate the unwanted and unacceptable noise, has been proposed in this paper.

To find out the main excitation sources of a bus floor's vibration, modal analysis and spectral analysis were respectively performed in the paper. First we tested the vibration modal of the bus's floor under the full-load condition, and the first ten natural frequencies and vibration modes were obtained for the source identification of the bus floor's vibration. Second the vibration characteristic of the bus floor was measured in an on-road experiment. The acceleration sensors were arranged on the bus's floor and the possible excitation sources of the bus, which includes engine mounting system, driveline system, exhaust system, and wheels. Then the on-road experiment was carefully conducted on a highway under the four kinds of test condition: in-situ acceleration, uniform velocity (90km/h, 100km/h, 110km/h, 120km/h), uniform acceleration with top gear, and stall sliding condition with neutral gear.

Torsional vibration of drive shaft has great influence on the vibration of vehicle. Reasonable phase arrangement of multi-universal coupling can attenuate vibration. In this paper, theoretical model of drive shaft with planar multi-cross universal coupling was established; the optimization scheme of the phase arrangement of multi-cross universal coupling was presented. The results of test validation and simulation show that the optimization scheme is effective and reasonable. The results of test validation and simulation show that the optimization scheme was effective and reasonable and the optimized scheme could solve the abnormal vibration on floor. Arranging phases of universal joints reasonably is very significative for attenuate the torsional vibration of drive shaft and the floor vibration.

Taking an off-road vehicle equipped with 32-speed binary logic automatic transmission (AT) as the research object, the slope starting control research is carried out. The slope starting process is divided into the overcoming resistance stage, the sliding friction stage, and the synchronization stage. The control strategies for each stage are designed respectively. Focusing on the control of the sliding friction stage, the equivalent two-speed model of the starting clutch is established, which realizes the calculation of the speed difference and the slip rate between the driving and driven ends of the starting clutch. Furthermore, the slope starting control strategy based on the proportional-integral-derivative (PID) control of the clutch slip rate is designed. Through the simulation tests of the vehicle starting at different slopes, the correctness of the slope starting control strategy has been verified by MATLAB/Simulink.

This paper studies a multi-objective optimization design of interior noise for an automotive body. An acoustic-structure coupled model with materials and properties was established to predict the interior noise based on a passenger car. Moreover, three kinds of approximation models related damping thickness and the root mean square of the driver’s ear sound pressure level were established through Latin hypercube method and the corresponding experiments. The prediction accuracy was analyzed and compared for the approximate response surface model, Kriging model and Radial Basis Function neural network model. On this basis, multi-objective optimization of the vehicle interior noise was conducted by using NSGA-II. According to the optimization results, the damping composite structure was applied on the car body structure. Then, the comparison of sound pressure level response at driver’s ear location before and after optimization was performed at speed of 60 km/h on a smooth road.

The mechanical properties of sandy road are quite different from those of hard surface road. For vehicle control systems such as EMS (engine management system), TCU (transmission control unit) and ABS (antilock brake system), the strategies and parameters set for solid surface road are not optimal for driving on sandy road. It is an effective way to improve the mobility of all-terrain vehicles by identifying sandy road online and shifting the control strategies and parameters of control systems to sandy sets. In this paper, a sandy road identification algorithm for SUVs is proposed. Firstly, the vehicle signals, such as engine torque and speed, gear position, wheel and vehicle speed, are acquired from EMS, TCU and ESP (electronic stability program) through CAN (controller area network) bus respectively. Based on the information and longitudinal force equilibrium equation, the travelling resistance of vehicle is estimated.

Since steering wheel torque feedback is one of the crucial factors for drivers to gain road feel and ensure driving safety, it is especially important to simulate the steering torque feedback for a driving simulator. At present, steering wheel feedback torque is mainly simulated by an electric motor with gear transmission. The torque response is typically slow, which can result in drivers’ discomfort and poor driving maneuverability. This paper presents a novel torque feedback device with magnetorheological (MR) fluid and coil spring. A phase separation control method is also proposed to control its feedback torque, including spring and damping torques respectively. The spring torque is generated by coil spring, the angle of coil spring can be adjusted by controlling a brushless DC motor. The damping torque is generated by MR fluid, the damping coefficient of MR fluid can be adjusted by controlling the current of excitation coil.

Improvement of shift quality evaluation has become more prevalent over the past few years in the development of automatic transmission electronic control system. For the problems of the subjective shift quality evaluation that subjectivity is too strong, the standard cannot be unified and the definition of the objective evaluation index is not clear at present, this paper studies on the methods of objective evaluation of shift quality based on the multi-hierarchical grey relational analysis. Firstly, objective evaluation index system is constructed based on physical quantities, such as the engine speed, the longitudinal acceleration of the vehicle and so on, which broadens the scope of the traditional objective evaluation index further.

Aiming at the low transmission efficiency and power density of the hydraulic automatic transmission (AT), and the increasingly complex structure of its planetary gear with the increase of transmission gears, this paper proposes a new type of binary logic transmission (BLT), which adopts the double internal meshing planetary row (DIMPR), based on a heavy-duty commercial vehicle. By introducing the concept of BLT and analyzing the transmission performance of the DIMPR, the process of scheme design of binary double internal meshing planetary gear transmission (BDIMPGT) is established. According to the structural characteristics of the DIMPG, the support structure of the planetary gear is designed based on CAD and CATIA. In the structural design of binary clutches, V-groove clutch parts are coupled to the transmission case, planetary carrier, and sun shaft, respectively, in each DIMPG.

In order to improve ride comfort and reduce interior noise of commercial vehicles, modal sensitivity analysis and optimization design of a commercial vehicle cab was carried out, which increased the first natural frequency of the optimized cab by 23.96%. The result of cab modal test verified the correctness of the finite element model and the effectiveness of the improving method. The structure-acoustic coupling model of the cab was established, and the acoustic response of the coupled sound field was predicted. The sound pressure level of the optimized cab was reduced. In comparison of the optimized cab with the original one, the optimization scheme was confirmed to be effective and reasonable.

Taking a good longitudinal braking performance on flat and level road of tractor and semi-trailer combination as a target, in order to achieve an ideal braking force distribution among axles, while the vehicle deceleration is just depend on the driver's intention, not affected by the variation of semi-trailer mass, the paper proposes a model based vehicle mass identification and braking force distribution strategy. The strategy identifies the driver's braking intention via braking pedal, estimates semi-trailer's mass during the building process of braking pressure in brake chamber, distributes braking force among axles by using the estimated mass. And a double closed-loop regulation of the vehicle deceleration and utilization adhesion coefficient of each axle is presented, in order to eliminate the bad effect of mass estimation error, and enhance the robustness of the whole algorithm. A simulation is conducted by utilizing MATLAB/Simulink and TruckSim.

This paper presents experimental studies of particulate emissions in a small SI engine fueled with LPG and gasoline fuels. A single cylinder, four-stroke, water-cooled, 125cc EFI engine with gasoline fuel is used as the baseline engine. Characteristics of the particulate emissions of the two fuels are compared. Test results show that: there are great quantities of particulate emissions for both fuels, but the total numbers of particulate emissions for the two fuels are generally in the same level. The distribution of the particulate sizes is in bimodal type for the gasoline, but for the LPG its first peak is not markedly in some conditions. The particulate sizes of the second peak for the two fuels appear at about the same size. At middle loads and 3000r/min, the particulate emissions for both of the two fuels are the greatest.

Based on a 125cm3 single cylinder SI engine, the designated idle speed was controlled by adjusting of cycle ignition advance angle. By analyzing the effects of different idle speed and throttle open position on three way catalyst (TWC) light-off time and conversion efficiency of HC and CO emissions, combined with the corresponding total HC and CO emissions level, the optimum idle speed and throttle open position at engine's warm-up phase were found by the matching optimum. The present method for engine control strategy is helpful to optimize the warm-up phase emission levels in SI engine with LPG fuel.

To reach the goal of optimal performance match between engine and transmission, the dynamic characteristics of engine should be taken into consideration. In the paper, the dynamic torque and fuel consumption models of engine, described by a multi-layers feed forward neural network, were established. Based on that, the methods used to calculate the optimal dynamic and economical shift schedules with dynamic 3-parameters were put forward. The shift schedule with dynamic 3-parameters based on neural network model is proven to be superior to the shift schedule with only 2-parameters in both dynamic performance and fuel economy by the test.

This paper presents an investigation of cold starts based on a cycle-by-cycle control strategy in an LPG EFI engine. Experiments were carried out in a four-stroke, water-cooled, single cylinder, 125cc SI engine with an EFI system. Effects of the first injection pulse width and the first combustion cycle on the characteristics of the cold-start were analyzed based on the histories of transient engine speeds and cylinder pressures. The study focuses on how to realize the controllable ignition cycle and the single-cycle and multi-cycle combustions were tested based on the single starting injection pulse width. Test results show that the first combustion cycle has an important effect on HC emission and combustion stability of following cycles at cold-start. The injection pulse width is the key factor determining the characteristics of an ignition cycle during the cold-start.